Skoda Fabia

since 2000 release

Repair and operation of the car


Skoda Fabia
+ 1.1. Description of the car
- 2. Engine
   2.1. Removal of the top casing of the engine
   + 2.2. Installation of the piston of the first cylinder in the provision of VMT of a step of compression
   2.3. Replacement of a belt of the drive of the generator
   + 2.4. Replacement and adjustment of a tension of a belt of the drive of the camshaft
   2.5. Replacement of a chain of the drive of the camshaft
   2.6. Selection of a distributive gear wheel of a bent shaft
   2.7. Replacement of laying of a head of the block of cylinders
   2.8. Replacement of an epiploon of the camshaft
   2.9. Replacement of oil scraper caps
   2.10. Replacement of a forward epiploon of a bent shaft
   2.11. Back epiploon of a bent shaft
   - 2.12. Repair of a head of the block of cylinders
      2.12.1. Dismantling
      2.12.2. Troubleshooting
      2.12.3. Assembly
      2.12.4. Grinding in of valves
      2.12.5. Adjustment of a starting position of hydropushers of valves
      2.12.6. Check of hydropushers of valves of engines of 1,0 l, 37 kW and 1,4 l, 50 kW
      2.12.7. Removal and installation of the engine
   + 2.13. Repair of the engine
+ 3. Lubrication system
+ 4. Power supply system
+ 5. Cooling system
+ 6. System of production of the fulfilled gases
+ 7. Transmission and running gear
+ 8. Steering
+ 9. Brake system
+ 10. Electric equipment
+ 11. Body
+ 12. Electrical circuitries




2.12.3. Assembly
GENERAL INFORMATION

Axis of yokes of valves assembled

1 – direct yoke;

2 – the yoke turned to the left;

3 – the yoke turned to the right;

4 – external rack of an axis of yokes;

5 – small rack of an axis of yokes;

6 – big rack of an axis of yokes

Marking of camshafts of engines with a working volume of 1,4 l

1 – inlet camshaft;

2 – final camshaft

The head of the block is collected as it should be, the return to dismantling, taking into account the following:

PERFORMANCE ORDER
1. Before installation oil engine cores of valves, working surfaces of hydropushers and yokes of valves, oil scraper caps, cams and necks of camshafts, axes of yokes.
2. At engines of 1,0 l, 37 kW and 1,4 l, 50 kW at assembly of axes of yokes of a yoke and rack arrange, as shown in rice. Axis of yokes of valves assembled.
3. At engines of 1,4 l, 55 and 74 kW before installation of epiploons 3 (see rice. Details of a head of the block of cylinders of engines of 1,4 l, 55 and 74 kW) oil engine their working edges. Replace bolts of 1 fastening of pulleys of camshafts and bolts of the 6th fastening of the case of bearings.
4. Marking of camshafts is shown on rice. Marking of camshafts of engines with a working volume of 1,4 l. On inlet distributive the inscription 036AC, and between cams of the third cylinder – DE is put to a shaft between cams of the first and second cylinders, on final distributive inscriptions 036AA and W1 are respectively put to a shaft.
5. At diesel engines of 1,9 l, 74 kW, before installation of covers of bearings, establish washers 4 (see rice. A head of the block of the diesel engine of 1,9 l, 74 kW), replace bolts of 1 fastening of axes of yokes and bolts of the 19th fastening of covers of bearings.
6. Before installation of covers of bearings apply sealant on the first and fifth covers, as shown in rice. Places of putting sealant on the first and fifth covers of bearings of the camshaft. Marking of the camshaft is shown in the drawing, at an end face of a cam of the final valve of the fourth cylinder the inscription 038R or 858R is put, and diameter and (the circle entered in a cam) is equal to 52,8 mm.