Skoda Fabia

since 2000 release

Repair and operation of the car


Skoda Fabia
+ 1.1. Description of the car
+ 2. Engine
+ 3. Lubrication system
+ 4. Power supply system
+ 5. Cooling system
+ 6. System of production of the fulfilled gases
- 7. Transmission and running gear
   + 7.1. Transmission
   - 7.2. Forward suspension bracket
      7.2.1. Removal and installation of a telescopic rack
      7.2.2. Repair of a telescopic rack
      7.2.3. Replacement of a spherical support
      7.2.4. Removal and installation of the lever of a forward suspension bracket
      7.2.5. Removal and installation of an arm of a forward suspension bracket
      7.2.6. Replacement of a rubber-metal support
      7.2.7. Removal and installation of the stabilizer of cross stability
   + 7.3. Back suspension bracket
+ 8. Steering
+ 9. Brake system
+ 10. Electric equipment
+ 11. Body
+ 12. Electrical circuitries




7.2. Forward suspension bracket

7.2.1. Removal and installation of a telescopic rack
GENERAL INFORMATION

Fastening of a spherical support

1 – lever of a forward suspension bracket;

2 – bolt;

3 – spherical support

Details of a rack of a forward suspension bracket

1 – rotary fist;
2 – nut;
3 – coupling bolt;
4 – damping rack;
5 – compression buffer;
6 – protection cover;
7 – spring of a forward suspension bracket; 		8 – persistent bearing of a support;
9 – rack support;
10 – rod nut;
11 – plate of a support;
12 – bolt of fastening of a rack;
13 – protective cap

Details of a beam of a forward suspension bracket

1 – beam;
2 – a nut of fastening are resistant to a stabilizer bar;
3 – stabilizer bar;
4 – bar pillow;
5 – pillow holder;
6 – a nut of fastening of a rack of the stabilizer to a telescopic rack;
7 – rack of the stabilizer of cross stability;
8 – arm;
9, 10, 19, 22 – bolts;
11 – rubber-metal support;
12 – lever of a forward suspension bracket;		 13 – lock plate;
14 – nut of a finger of a spherical support;
15 – spherical support;
16 – bolt of fastening of a spherical support;
17 – air duct;
18 – percussion caps;
20 – beam arm;
21 – bolt of fastening of the steering mechanism;
23 – bolts of fastening of a back support of the power unit to the transmission;
24 – a bolt of fastening of a back support of the power unit to a beam;
25 – back support of the power unit

PERFORMANCE ORDER
1. Weaken an inhaling of bolts 9 (see rice. Details of a forward suspension bracket) fastenings of the corresponding wheel and nut of the 10th nave.
2. Raise and establish a forward part of the car on reliable support.
3. Remove a forward wheel, having finally turned off bolts of its fastening.
4. Turn off a nut of the 26th fastening and disconnect a rack of the 27th stabilizer of cross stability from a telescopic rack 1.
5. Disconnect wires from the sensor 24 frequencies of rotation of a wheel. Turn off a bolt of the 25th fastening and remove the sensor 24 frequencies of rotation of a wheel.
6. Remove a support 13 and suspend it on a wire to a body (see subsection 9.5.1) or (see subsection 9.6.1).
7. Mark the provision of bolts 2 (see rice. Fastening of a spherical support) fastenings of the spherical hinge on the lever of 1 suspension bracket, having led round contours of heads of bolts. It will help to keep approximately after assembly the angles of installation of wheels.
8. Turn off bolts 2 fastenings of a spherical support 3 to the lever.
9. By means of a special stripper 1 (see fig. of Vypressovk of a shlitsevy tip of the external CV JOINT from a nave) a vypressuyta a shlitsevy tip of the external CV JOINT from a nave 2 wheels. In the absence of a stripper it can be made blows of the hammer through a wooden pro-rate on an end face of a shlitsevy tip.
10. Suspend the wheel drive to a body by means of a wire.
11. Disconnect steering draft from a rotary fist (see subsection 8.4.1) and suspend it on a wire to a body.
12. In podkapotny space turn off three bolts 12 (see rice. Details of a rack of a forward suspension bracket) fastenings are resistant to a body and remove a rack through a wheel niche.
13. Establish a telescopic rack upside-down, having replaced nuts of a nave and a spherical finger of a tip of steering draft, and also bolts 16 (see rice. Details of a beam of a forward suspension bracket) fastenings of a spherical support and their lock plate 13. First of all roll bolts 12 (see rice. Details of a rack of a forward suspension bracket) fastenings are resistant from a motor compartment.

Moments of an inhaling, N · m

Wheel nave nut
30
Bolts of fastening of the spherical hinge to the suspension bracket lever
20, then to tighten on 90 °
Nut of a spherical finger of a tip of steering draft
20, then to tighten on 90 °
Nut of fastening of a rack of the stabilizer of cross resistance to a forward rack
40
Bolts of the top fastening of a forward rack
25
Bolt of fastening of the sensor of frequency of rotation of a wheel
8
Bolts of fastening of a wheel
120