Skoda Fabia

since 2000 release

Repair and operation of the car



Skoda Fabia
+ 1.1. Description of the car
+ 2. Engine
+ 3. Lubrication system
+ 4. Power supply system
+ 5. Cooling system
+ 6. System of production of the fulfilled gases
+ 7. Transmission and running gear
+ 8. Steering
- 9. Brake system
   - 9.1. Pedal knot
      9.1.1. Removal and installation
      9.1.2. Replacement of plugs of a pedal of a brake
   9.2. Vacuum amplifier
   9.3. Main brake cylinder
   9.4. Pressure regulator (on models without ABS)
   + 9.5. The brake mechanism of a forward wheel like FS III
   + 9.6. The brake mechanism of a forward wheel like FS II
   + 9.7. Brake mechanism of a back wheel (drum)
   + 9.8. Brake mechanism of a back wheel (disk)
   + 9.9. Parking brake
   + 9.10. Anti-blocking system (ABS)
+ 10. Electric equipment
+ 11. Body
+ 12. Electrical circuitries




9.1. Pedal knot

9.1.1. Removal and installation

GENERAL INFORMATION

Brake pedal detachment from a pusher of the vacuum amplifier

1 – brake pedal;

2 – arm;

3 – metal core

Pedal knot

1 – brake pedal;
2 – slip;
3 – plastic plug;
4 – axis plug;
5 – arm;
6, 14 – nuts;
7 – pusher of the vacuum amplifier;
8 – vacuum amplifier;
9 – front board;
10 – dashboard arm;
11 – support of the amplifier;
12 – bolt;
13 – pedal axis;
15 – signal switch
braking;
16 – accelerator pedal

Fastening of pedal knot

1 – brake pedal;

2, 5 – nuts;

3 – arm;

4 – accelerator pedal

Connection of a pedal of a brake to a pusher of the vacuum amplifier

1 – pusher of the vacuum amplifier;

2 – arm;

3 – brake pedal

Prevention

You watch that additional rugs on a floor did not reduce the brake pedal course.


Removal

PERFORMANCE ORDER
1. Disconnect a wire from the - plug of the rechargeable battery.
2. Remove a ware box from the driver.
3. Turn off a bolt of fastening and remove an air duct of an obduv of legs of the driver (see subsection 11.6). On the models equipped with the Comfort system remove the central control unit.
4. Remove the braking signal switch (see subsection 9.10.7).
5. Disconnect a block from the sensor of provision of a pedal of an accelerator.
6. Disconnect a brake pedal from a pusher of the vacuum amplifier.
7. For this purpose press against the stop a pedal 1 (see rice. A brake pedal detachment from a pusher of the vacuum amplifier) brakes also insert a suitable metal core 3 into openings for the switch of a signal of braking of an arm 2 and pedals.
8. Pull a pedal 1 on yourself, having squeezed out from a clamp in a pedal by means of a core a spherical tip of a pusher 7 (see rice. Pedal knot).
9. Turn off two plastic nuts 1 (see rice. Fastening of a casing of the driveshaft of a steering column) fastenings of a casing of the driveshaft of a steering column also remove a casing 2.
10. Turn off six nuts of the 2 and 5 fastening of an arm of pedal knot (see rice. Fastening of pedal knot – the top nut in this drawing is not visible, all nuts are shown on rice. Pedal knot, poses. 14).
11. Remove pedal knot from hairpins.

Installation

PERFORMANCE ORDER
1. Establish pedal knot upside-down.
2. Replace nuts of fastening of pedal knot new.
3. Record 3 brakes in a pedal (see rice. Connection of a pedal of a brake to a pusher of the vacuum amplifier) a spherical tip of a pusher of 1 vacuum amplifier.

The moment of an inhaling of nuts of fastening of an arm of pedal knot – 28 N · m.