Skoda Fabia

since 2000 release

Repair and operation of the car



Skoda Fabia
+ 1.1. Description of the car
+ 2. Engine
+ 3. Lubrication system
+ 4. Power supply system
+ 5. Cooling system
+ 6. System of production of the fulfilled gases
+ 7. Transmission and running gear
- 8. Steering
   8.1. Removal and installation of a steering wheel
   8.2. Removal and installation of returnable and contact rings assembled
   + 8.3. Steering column
   + 8.4. The steering mechanism (without amplifier)
   - 8.5. The steering mechanism (with the amplifier)
      8.5.1. Replacement of a tip of steering draft
      8.5.2. Removal of the steering mechanism
      8.5.3. Installation of the steering mechanism
      8.5.4. Replacement of steering draft
      8.5.5. Pump unit
      8.5.6. Check of electric chains of the amplifier of steering
      8.5.7. Replacement of the sensor of the amplifier of steering
      8.5.8. Replacement of highways of system of the amplifier of steering
      8.5.9. Check of level of working liquid
      8.5.10. Filling and removal of air from hydraulic system
      8.5.11. Check and adjustment of angles of installation of wheels
+ 9. Brake system
+ 10. Electric equipment
+ 11. Body
+ 12. Electrical circuitries



8.5.3. Installation of the steering mechanism

GENERAL INFORMATION

Details of the steering mechanism (with the amplifier)
1 – tip;
2 – lock-nut;
3 – external collar;
4 – protective cover;
5 – internal collar;
6 – bolt;
7 – heat-insulating screen;
8 – steering draft;
9 – pillow;
10 – fixing bracket;
11 – sealant;
12 – case of the steering mechanism;
13 – shaft of a driving gear wheel of the steering mechanism;
14 – laying;
15 – sensor of the amplifier of steering;
16 – bolt of fastening of the sensor of the amplifier of steering;
17 – lath of the steering mechanism

PERFORMANCE ORDER
1. Check and, if necessary, adjust the provision of a lath of the steering mechanism (see subsection 8.4.4).
2. Grease with soap solution a pillow 9 (see rice. Details of the steering mechanism (with the amplifier)) support of the steering mechanism to facilitate installation on it a fixing bracket 10.
3. Install the steering mechanism 22 (see rice. Fastening of the steering mechanism on the car (with the amplifier)) on a beam of 21 forward suspension brackets also screw new bolts of the 18th his fastening, finally without tightening them.
4. Check correctness of installation of a sealant 11 (see rice. Details of the steering mechanism (with the amplifier)) on the case of the steering mechanism.
5. Carefully lift a beam so that it was possible to connect highways and the sensor to the steering mechanism, having entered at the same time into a front board opening a shaft of a driving gear wheel of the steering mechanism.
6. Connect the sensor 6 (see rice. Fastening of the steering mechanism on the car (with the amplifier)) the amplifier to the steering mechanism, having established new laying 5, also fix by two bolts 7 with internal hexagons.
7. Connect to a case of the steering mechanism pressure head 16 and returnable 12 highways, using at the same time new sealing rings 13 and 15. Pay attention, at the returnable highway a sealing ring of round section.
8. Fix a beam of a forward suspension bracket.
9. Tighten the corresponding moment new bolts of the 18th fastening of the steering mechanism to a beam of a forward suspension bracket.
10. Connect steering thirsts for rotary levers.
11. Connect racks to a bar of the stabilizer of cross stability and put the clamps of fastening.
12. Attach a back support 20 to the transmission two new bolts 19.
13. On models with the reception pipe of the muffler passing under a beam of a forward suspension bracket establish a reception pipe with converter.
14. Establish an antisplash guard and forward wheels.
15. Lower the car on wheels.
16. Record a wire of the sensor of the amplifier of steering in three holders 4 (see rice. Elements of the hydraulic amplifier of steering).
17. Put on a shaft of a driving gear wheel of the steering mechanism a fork 3 (see rice. Fastening of the steering mechanism on the car (with the amplifier)) the cardan hinge also record a fork a new coupling bolt 4.
18. Insert into a front board opening a sealant 11 (see rice. Details of the steering mechanism (with the amplifier)). Make sure that it settled down exactly and densely.
19. Establish a casing 2 (see rice. Fastening of a casing of the driveshaft of a steering column) the driveshaft of a steering column also fix it by two plastic nuts 1.
20. Fill in working liquid in hydraulic system of the amplifier of steering (see subsection 8.5.10).
21. Install into place the rechargeable battery.
22. Install the air filter if it was removed.
23, Check and, if necessary, adjust the angles of installation of wheels.
24. It is recommended to check for service stations work of an electric part of system of the amplifier of steering by means of the special electronic device.

Moments of an inhaling, N · m

Bolts of fastening of the steering mechanism to a beam of a forward suspension bracket
50, then to tighten on 90 °
Bolts of fastening of a back support to the transmission
30, then to tighten on 90 °
Nuts of fastening of a bar of the stabilizer of cross resistance to racks
40
Bolts of fastening of the sensor of the amplifier of steering
6
Hollow bolt of fastening of the pressure head highway to a case of the steering mechanism
35
Nut of fastening of the returnable highway to a case of the steering mechanism
30
Coupling bolt of a fork of the cardan hinge
20, then to tighten on 90 °
Bolts of fastening of the heat-insulating screen
10
Bolts of fastening of a wheel
120