Skoda Fabia
+ 1.1. Description of the car
+ 2. Engine
+ 3. Lubrication system
+ 4. Power supply system
+ 5. Cooling system
+ 6. System of production of the fulfilled gases
- 7. Transmission and running gear
+ 7.1. Transmission
+ 7.2. Forward suspension bracket
- 7.3. Back suspension bracket
7.3.1. Removal and installation of a nave of a wheel (drum brake mechanism)
7.3.2. Removal and installation of a nave of a wheel (disk brake mechanism)
7.3.3. Removal and installation of a pin (drum brake to mechanisms)
7.3.4. Removal and installation of a pin (disk brake mechanism)
7.3.5. Removal and installation of the shock-absorber
7.3.6. Removal and installation of a spring
7.3.7. Removal and installation of a back suspension bracket
7.3.8. Check and adjustment of angles of installation of wheels
+ 8. Steering
+ 9. Brake system
+ 10. Electric equipment
+ 11. Body
+ 12. Electrical circuitries
|
Details of a back suspension bracket with drum brakes
1 – bolt of fastening of a wheel;
2 – screw of fastening of the brake drum;
3 – brake drum;
4 – protective cap;
5 – nave nut;
6 – nave;
7 – bolt of fastening of a board of a brake;
8 – brake mechanism assembled;
9 – holder of a cable;
10 – cable of the parking brake;
11 – arm;
12 – bolt of fastening of an arm;
13 – pressure regulator;
14 – bolt of fastening of the regulator;
15 – bolt of fastening of a load spring;
16 – spring holder;
17 – rubber-metal support; |
18 – beam of the back bridge;
19 – axis pin;
20 – brake tube;
21 – beam of a back suspension bracket (execution option);
22, 29 – nuts;
23 – bolt of the lower fastening of the shock-absorber;
24 – sensor of frequency of rotation of a wheel;
25 – a cap (for cars without ABS);
26 – bolt of fastening of the sensor;
27 – lower laying of a spring;
28 – bolt of fastening of a beam of the back bridge;
30 – arm of fastening of a back suspension bracket;
31 – spring of a back suspension bracket;
32 – top laying of a spring;
33 – bolt of the top fastening of the shock-absorber;
34 – shock-absorber;
35 – holder of the shock-absorber |
Details of a back suspension bracket with disk brakes
1 – a guide of blocks with a support assembled;
2 – bolt of fastening of a wheel;
3 – screw of fastening of a brake disk;
4 – brake disk;
5 – protective cap;
6 – nave nut;
7 – nave;
8 – bolt of fastening of a board of a brake;
9 – brake board;
10 – holder of a cable;
11 – cable of the parking brake;
12 – spring holder;
13 – rubber-metal support;
14 – beam of the back bridge; |
15 – axis pin;
16 – bolt of fastening of a guide of blocks;
17 – brake tube;
18, 24 – nuts;
19 – bolt of the lower fastening of the shock-absorber;
20 – sensor of frequency of rotation of a wheel;
21 – bolt of fastening of the sensor;
22 – lower laying of a spring;
23 – bolt of fastening of a beam of the back bridge;
25 – arm of fastening of a back suspension bracket;
26 – spring of a back suspension bracket;
27 – top laying of a spring;
28 – bolt of the top fastening of the shock-absorber;
29 – shock-absorber;
30 – holder of the shock-absorber |
Back suspension bracket semi-independent, lever and spring, with the longitudinal levers pivotally fixed on a body of the car and connected among themselves by a cross beam of U-shaped type. Longitudinal levers are connected to a body saylent-blocks. Suspension bracket springs twisted, with the reduced diameter of trailer rounds. That noise and vibration were not transferred to a body, the top and lower ends of springs lean on elastic support. |
|